This British Standard is the official English language version of. EN Together wi th BS EN i t supersedes. BS EN l which. BS EN BRITISH STANDARDOffshore containers and associated lifting sets — Part 1: Offshore containers — Design, manufacture. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European.

Author: Tatilar Aranris
Country: Cambodia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 8 May 2017
Pages: 387
PDF File Size: 14.32 Mb
ePub File Size: 15.18 Mb
ISBN: 553-3-26357-986-5
Downloads: 6696
Price: Free* [*Free Regsitration Required]
Uploader: Malalar

Conception, construction et marquageTeil 1: For other primary structure, the use of fillet welds shall be justified by design appraisal including calculations and consideration of failure modes. The offshore container shall show no permanent deformation or other damage after testing. Only materials with non- ageing properties shall be used.

NOTE A minimum of 12 are generally required. The information on the plate shall be in the English language. The marking shall be carried out in such a way as to avoid incorrect interpretation e. Only materials with non-ageing properties shall be used.

NOTE 2 When preparing the specification for a service container, it is advised that the rating is chosen higher than the estimated fitted out mass, i. For details of these and other benefits contact Membership Administration. In addition, each container shall be marked with a unique container number, issued by the owner, as a prime identifier for use as the common cross-reference on all in-service certification and shipping documentation. Tanks for dangerous cargoes shall fulfil the requirements of the IMDG Code, and shall be designed according to a recognized code for pressure vessels.

Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. This part of EN specifies only transport related requirements.

  A ROSE IN WINTER BY KATHLEEN E WOODIWISS PDF

It shall be held for 5 minutes before measurements are taken.

BS EN 海岸集装箱及其相关提升设备 第1部分:海岸集装箱 设计丶制造和标记 – MBA智库文档

1207-1 NOTE For containers with exposed aluminium, the danger of sparks caused by the impact of aluminium against corroded steel the thermite reaction should be taken into account.

Beams een be spaced sufficiently close together to give the necessary protection. To determine the resulting sling force on the pad eyes, the sling angle shall be taken into account, so that the resulting sling force on each pad eye is calculated as follows: Welding consumables shall be according to the relevant European standards for welding consumables Tensile testing shall be carried out according to EN To avoid confusion, the plate shall not carry the date of the next inspection.

The BSI copyright notice displayed in this document indicates when the document was e issued. Such service containers, as defined in paragraph 3.

Where a container is fitted with fork pockets designed for handling the container only when empty e. NOTE 1 This floor may be covered with a sheathing of wooden planks with a thickness not exceeding 50 mm.

Full text of “Safety British Standards”

In addition, the side rails and end rails in the base shall be able to withstand vertical point forces of 0,25 R g at the centre span. Pockets shall be located as far apart as practicable but need not be more than 2 mm apart from the centre of pocket to centre of pocket. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.

Doors shall be capable of being secured in the open position.

BS EN 12079-1:2006

NOTE The inspection body may require other or additional tests and examinations. No significant permanent damage shall occur.

  ILMU ULAT SUTRA PDF

wn Where applicable the lower edge of the marking shall be positioned near the side of the container in which the door is located.

The manufacturer shall ensure the quality of his procedures and facilities through operation of a quality assurance system at least in accordance with EN ISO Side and roof panels, including corrugated panels, are not considered to be part of the primary structure 3. Non-alloy quality and special steels.

Offshore-Container und zugehoerige Anschlaggarnituren. All materials for primary structures shall be identifiable against the certificates. For undated references, the latest edition of the referenced document including any amendments applies.

The examination shall be carried out in a 1279-1 providing sufficient lighting and other facilities necessary to allow the examination to be carried out safely and effectively. NOTE Provision for an additional language may be made.

Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 29 and a back cover. Tank containers built before that date may be in accordance with Chapter 13 of the older IMDG code i. To achieve this the internal load shall be taken as 2,5 R – T g evenly distributed over the container floor. Maximum gross mass excluding lifting set kg at Degrees from Vertical Tare mass: Guidance for ferritic steels.

Use of other alloys or tempers shall be subject to special consideration. NOTE 1 A minimum of 12 is recommended. NOTE Maximum vertical impact forces are likely to occur when a container is lowered onto the deck of a heaving supply vessel.